How do you change wiper blades on a 2014 Dodge Ram 1500?

Changing Wiper Blades on a 2014 Dodge Ram 1500
To change the wiper blades on a 2014 Dodge Ram 1500, you can follow these steps:
1. Select the Correct Wiper Blades: Ensure that you select the correct size blades for your 2014 Ram 1500. In most Rams, the driver side wiper blade is larger than the passenger side blade, so it’s important to get the correct size blades for your vehicle.
2. Remove the Old Blades:
– Start on the driver’s side of your 1500. Most blades are held in place with a tiny clip. Push that clip up towards the arm and push the blade backwards, as if you were sliding it down the wiper arm.
– When removing the old blades, be cautious not to pull too hard, as excessive force may be required to disengage them from the wiper arm.
3. Install the New Blades:
– Position the new blade so that the hook is pointing at the wiper attachment. The hook will go over the top of the attachment. Pull the blade toward the end of the arm. You’ll hear a click when it locks into position. Repeat the process on the passenger side of your 1500.
4. Maintenance Tips:
– It’s recommended to replace both windshield wiper blades, even if only one side is streaking, as the rubber on the opposite side is likely worn as well.
– To enhance the longevity of your 1500’s wiper blades, it’s advised to scrape off the ice and snow from the windshield before using your wipers, as a layer of ice can reduce the effectiveness of the rubber wiper blade.
Remember, if you are unsure or uncomfortable with the process, it’s always a good idea to seek professional help for changing your windshield wiper blades.

Can I replace my windshield wipers myself?

And then slide the blade down to release it from the hook. Here. It is from another angle. Once you’ve removed the blade. You can reinstall new wiper blades by reversing this process.

Do you need a tool to change windshield wipers?

Most cars don’t require tools to replace windshield wiper blades; you’ll need only both hands. Locate the blades on your car and lift the wiper arms into the air. Usually they’ll hold themselves in place under spring tension, allowing you room to easily switch out the blades.

What size wiper blades for a Ram 1500?

24″
The Ram 1500 requires a specific wiper size, so you’ll need to ensure the size wiper you get fits your truck. For the current year model, the sizes are: Driver’s side: 24″ Passenger side: 24″

How do you properly remove and replace a wiper blade?

Put your fingers in between here. Pull it through. Slide it right out just like that very simple.

Do you buy 2 different size wiper blades?

Windshield wiper blades are vehicle specific. On some vehicles, both wiper blades are the same size. On other vehicles, the two wiper blades are different sizes. The optimal wiper blade size is determined by the manufacturer and selected for proper fit to clear as much of the windshield as possible.

How do I remove my windshield wiper blades?

On the wiper blade assembly press it. And while holding it down gently. Slide the blade off the wiper arm repeat.

How do you change a hook arm windshield wiper?

Down push your little plastic. Piece in slide it over the arm. And slides right back up clicks into place. And lower it back down it’s that easy.

How do you unclip windshield wipers?

Take off Windshield Wipers: To remove a windshield wiper, gently lift the arm away from the windshield, then press the small tab under the wiper where it meets the arm. The wiper blade should then slide right off the arm when you pull downward.

How do you change a Dodge windshield wiper?

Now. Use one hand to steady the arm. And the other to push the blade away from the j-hook. And toward the windshield. With the Locking tab open position the replacement wiper blade under the j-hook.

How to change windshield wipers on a Dodge Ram 1500?

And toward the windshield. Position the replacement wiper blade under the j-hook. And insert the bracket into the hook. Slide the wiper up until it clicks.