How do you change the wiper blades on a 2016 Toyota Highlander?

Changing Wiper Blades on a 2016 Toyota Highlander
To change the wiper blades on a 2016 Toyota Highlander, you can follow these general steps:
1. Prepare the new wiper blades: Purchase the appropriate wiper blades for your Toyota Highlander. The driver’s side wiper blade is often longer than the passenger side, so make sure to get the correct sizes for each side.
2. Position the wipers: Turn on the wipers and then turn off the Toyota Highlander when the wipers are at their mid-way point on the windshield. This will make it easier to lift the wipers away from the windshield and access them for replacement.
3. Remove the old wiper blades: Lift the wipers up and away from the windshield. Take note of which new blade length goes on which side. Look for a button or latch to lift and slide off the old wiper blade. The old wipers should stick out, away from the windshield, allowing for easy access during the rest of the changing process.
4. Attach the new wiper blades: Place the small bar attachment on the new wiper blade into the hook on the wiper arm. Rotate the blade away from you until it snaps into place. If you removed the cover from the base of the wiper arm, put it back into place .
5. Repeat for the other side: Repeat the process for the other wiper blade on the passenger side of your Toyota Highlander.
Always check your vehicle’s owner’s manual for specific instructions on changing your wiper blades before removing or installing them.
Please note that these steps are general guidelines, and it’s always a good idea to consult your vehicle’s owner’s manual for specific instructions tailored to your Toyota Highlander model.

How do you remove wiper blades?

On the wiper blade assembly press it. And while holding it down gently. Slide the blade off the wiper arm repeat.

Do you buy 2 different size wiper blades?

Windshield wiper blades are vehicle specific. On some vehicles, both wiper blades are the same size. On other vehicles, the two wiper blades are different sizes. The optimal wiper blade size is determined by the manufacturer and selected for proper fit to clear as much of the windshield as possible.

How do you release windshield wipers?

And then put your fingers in between. Where. It slides in and just pull and it comes undone from this clip. Now this is obviously this style windshield wiper it’s the hook style.

How do you change wiper blades on a Toyota Highlander?

And then you’re locking it in place once you feel that it’s locked in place. And you kind of push it in then. You’ll know that it’s fully installed you’re going to close that latch.

Is it hard to change windshield wiper blades?

And locks. On just like that now the wiper blade can’t come. Off. We open up that little arm. And the blade can slide right off now we’re ready to put our new wiper blade. On.

How do you change a Toyota windshield wiper?

First pull away the wiper arm from the screen then tilt the blade. So it’s horizontal look for the release tab. Open it and slide the arm. Off find the open end of the rubber insert. And pull it out

How do I know what size wipers I need?

First, check your owner’s manual. While typically an OEM does not provide a standard wiper size, your owner’s manual may provide one, depending on your vehicle’s make and model. If that’s not the case, you can either: Using a tape measure, measure your existing wiper blades — driver side, passenger side, and rear.

How do you remove the wiper blades on a 2016 Toyota Highlander XLE?

Grab this little tab. And pull up lift the wiper arm up twist. Down and push down. And that will allow you to release the wiper do not let go of this and let it smack the windshield. It can crack the

What size wiper blades for Toyota Highlander?

Toyota Highlander Wiper Size Comparison Chart

Year	Driver Side	Passenger Side
2021	24″ – 26″	18″
2020	24″ – 26″	18″
2019	26″	20″
2018	26″	20″

Can I change my own wiper blades?

And then slide the blade down to release it from the hook. Here. It is from another angle. Once you’ve removed the blade. You can reinstall new wiper blades by reversing this process.