To change the spark plugs on a 2012 Chevy Traverse, you will need to follow these steps:
Step 1: Gather the necessary tools and materials
Before you begin, make sure you have the following tools and materials:
– New spark plugs (compatible with your Chevy Traverse)
– Socket wrench
– Spark plug socket
– Extension bar
– Torque wrench
– Dielectric grease (optional)
Step 2: Prepare the vehicle
Ensure that the engine is cool before starting the process. It’s also a good idea to disconnect the negative terminal of the battery to prevent any electrical mishaps.
Step 3: Locate the spark plugs
The spark plugs are located on the top of the engine, underneath the ignition coil packs. You may need to remove any engine covers or components that obstruct access to the spark plugs.
Step 4: Remove the ignition coil packs
Using a socket wrench, remove the bolts securing the ignition coil packs. Gently disconnect the electrical connectors from each coil pack and set them aside. Be careful not to damage the connectors.
Step 5: Remove the old spark plugs
Attach a spark plug socket to the extension bar and carefully loosen and remove each spark plug. Take note of the order in which the spark plugs are removed to ensure proper reinstallation.
Step 6: Install the new spark plugs
Apply a small amount of dielectric grease to the inside of the spark plug boots (optional). Insert the new spark plugs into the spark plug socket and carefully thread them into the engine by hand. Once they are hand-tight, use a torque wrench to tighten them to the manufacturer’s recommended torque specification. Be careful not to overtighten.
Step 7: Reinstall the ignition coil packs
Reattach the ignition coil packs to their respective spark plugs. Make sure they are securely in place and reconnect the electrical connectors.
Step 8: Finalize the process
Double-check that all connections are secure and that everything is properly reinstalled. Reconnect the negative terminal of the battery if it was disconnected earlier.
And that’s it! You have successfully changed the spark plugs on your 2012 Chevy Traverse. Remember to dispose of the old spark plugs properly and consult your vehicle’s manual or a certified mechanic if you encounter any difficulties.
Please note that the information provided above is based on general knowledge and may vary depending on the specific model and configuration of your Chevy Traverse. It’s always a good idea to consult the vehicle’s manual or seek professional assistance for detailed instructions tailored to your vehicle.
Contents
- Is it cheaper to change your own spark plugs?
- How often should spark plugs be changed Chevy Traverse?
- How much does it cost to change spark plugs in a 2012 Chevy Traverse?
- How do you know when you need new spark plugs?
- Is it OK to change spark plugs yourself?
- How much are spark plugs for a Chevy Traverse?
- How many spark plugs does a 2012 Chevy Traverse have?
- How do I know when my spark plugs need replacing?
- What is the spark plug gap for a 2012 Chevy Traverse?
- Is it cheaper to replace spark plugs yourself?
Is it cheaper to change your own spark plugs?
If it’s a task you aren’t comfortable doing on your own, spark plug replacement cost at a repair shop will have labor costs higher than the parts. For instance, a set of four spark plugs in a compact car will likely be around $50 to $80 to install.
How often should spark plugs be changed Chevy Traverse?
97,500 Miles
97,500 Miles—spark Plug Service
Replace your spark plugs at 97,500 miles of driving. Your technician will inspect your spark plug wires at this point as well. Spark plugs may be small, but they’re essential for your drive.
How much does it cost to change spark plugs in a 2012 Chevy Traverse?
The average cost for a Chevrolet Traverse Spark Plug Replacement is between $309 and $366. Labor costs are estimated between $215 and $271 while parts are priced between $94 and $95. This range does not include taxes and fees, and does not factor in your unique location. Related repairs may also be needed.
How do you know when you need new spark plugs?
The most common signs of bad spark plugs include start-up trouble, rough idling, sluggish acceleration, declining fuel economy, engine misfiring, and engine knocking.
Is it OK to change spark plugs yourself?
If you’re not comfortable with that, take your vehicle to a pro. But if your engine affords easy access to the rear bank, you can probably do the job yourself. Just be sure you gap the spark plugs properly and use a torque wrench. The tools shown are available at online suppliers and auto parts stores.
How much are spark plugs for a Chevy Traverse?
AutoNation Mobile Service offers upfront and competitive pricing. The average cost for Chevrolet Traverse Spark Plugs Replacement is $367.
How many spark plugs does a 2012 Chevy Traverse have?
Iridium IX spark plug. Quantity per car: 6.
How do I know when my spark plugs need replacing?
5 Signs You Need New Spark Plugs
- Engine Misfires. A misfiring engine is a big sign that one or more of your spark plugs are not firing properly.
- Poor Gas Mileage. When spark plugs are working correctly, they burn fuel efficiently in your engine.
- Trouble Starting.
- Slow Acceleration.
- Rough Idling.
What is the spark plug gap for a 2012 Chevy Traverse?
6 pc NGK Laser Platinum Spark Plugs for 2009-2017 Chevrolet Traverse 3.6L V6
| Year Range | Make | Notes |
|---|---|---|
| 2011 | Chevrolet | 3.6L V6;Gap 0.044″ |
| 2012 | Chevrolet | 3.6L V6;Gap 0.044″ |
| 2013 | Chevrolet | 3.6L V6;Gap 0.044″ |
| 2014 | Chevrolet | 3.6L V6;Gap 0.044″ |
Is it cheaper to replace spark plugs yourself?
Replacing spark plugs is usually a straightforward job. If you do it yourself—which should take about an hour for a four-cylinder engine—you’ll save on labor costs.
