How do you bleed the brakes on a 2016 Chevy Trax?

Bleeding the Brakes on a 2016 Chevy Trax
To bleed the brakes on a 2016 Chevy Trax, you can follow these steps:
1. Gather the necessary tools: You will need a wrench, a clear plastic tube, a container to collect the brake fluid, and a bottle of fresh brake fluid.
2. Locate the brake bleeder screws: The brake bleeder screws are located on each brake caliper or wheel cylinder. There should be one bleeder screw for each wheel.
3. Prepare the brake fluid: Make sure you have a bottle of fresh brake fluid that is compatible with your vehicle’s specifications. Check the owner’s manual or consult a professional if you are unsure about the correct type of brake fluid to use.
4. Start with the wheel farthest from the master cylinder: Begin with the wheel farthest from the master cylinder, which is typically the right rear wheel. This ensures that you remove all the air from the brake lines.
5. Attach the clear plastic tube: Attach one end of the clear plastic tube to the brake bleeder screw and place the other end into the container to collect the brake fluid.
6. Open the bleeder screw: Use a wrench to loosen the bleeder screw, but do not remove it completely. This allows the brake fluid and air to escape from the system.
7. Have an assistant press the brake pedal: Instruct your assistant to slowly press the brake pedal and hold it down. This will force the brake fluid and air out of the system.
8. Close the bleeder screw: Once the brake pedal is fully depressed, tighten the bleeder screw to prevent air from entering the system. Instruct your assistant to release the brake pedal slowly.
9. Repeat the process: Repeat steps 6-8 until you see a steady stream of brake fluid without any air bubbles. Start with the wheel farthest from the master cylinder and work your way towards the closest wheel.
10. Check the brake fluid level: Throughout the bleeding process, make sure to check the brake fluid level in the master cylinder reservoir. Keep it topped up to prevent air from entering the system.
11. Repeat for other wheels: Once you have completed bleeding the brakes for one wheel, move on to the next wheel and repeat the process.
Remember, if you are not comfortable performing this procedure yourself, it is recommended to schedule service at a dealership or consult a professional to ensure the job is done correctly and safely.
I hope this helps! Let me know if you have any other questions.

How do you bleed air from brakes by yourself?

But just about this size is what you want. I drilled two holes in the cap. This is 3 16 fuel line that’s what you want to use because it sits pretty tight on top of the bleeder screw.

Does the engine need to be running to bleed brakes?

The vehicle should not be running at any time during the bleeding process. If you are using a DIY system, these steps require a partner: With your partner in the driver’s seat, have them slowly pump the brake pedal two times and then hold the brake pedal to the floor. Have them yell out pressure when the pedal is down.

What is the bleeding sequence for Chevy brakes?

Usually, you want to bleed your brakes in the following order: passenger-side rear, driver-side rear, passenger-side front, driver-side front. In other words, you’re starting farthest from the master cylinder and working your way closer.

How do you bleed the brakes on a 2017 Chevy Trax?

Procedure. Finished that’s how to perform ABS. Bleeding.

How many times do you pump brakes when bleeding?

Instruct the assistant to “apply.” The assistant should pump the brake pedal three times, hold the pedal down firmly, and respond with “applied.” Instruct the assistant not to release the brakes until told to do so. Loosen the bleeder screw with a brief ¼ turn to release fluid into the waste line.

How do you bleed GM brakes with ABS?

In general, whenever you are bleeding an ABS-equipped vehicle you can do so exactly as you would any other vehicle – stroke the pedal to pressurize the system, open a bleeder, close the same bleeder, and repeat. This does not change whether you are pressure-bleeding, vacuum-bleeding, or manual-bleeding.

Do you bleed brakes with reservoir cap on or off?

Locate your brake master cylinder reservoir’s brake fluid level, usually located under-the-hood. Ensure that your car has the appropriate amount of fluid. While you’re bleeding the brakes, you’ll want to be sure that you leave the master cylinder cap unscrewed but rest it on top of the reservoir.

How do you get air out of brake lines without bleeding them?

To get air out of your brakes, you have to bleed them. There’s no two ways around it—to remove the air it has to be replaced with new fluid. That may seem easy enough (and it is, for an experienced mechanic) but doing any DIY on your brakes is dangerous.

How do you bleed a Chevy ABS module?

But if air has entered the modulator, the system will have to be bled using a pressure bleeder and scan tool:

1. Connect the pressure bleeder to the master cylinder reservoir.
2. Turn the ignition on.
3. With bleeder screws closed, pressurize the system to 35 psi.
4. Select the “Automatic Bleed Procedure” on the scan tool.

Do you need a special tool to bleed ABS brakes?

No scan tool is needed to bleed brakes because its such a simple procedure. Some vehicles do require a scan tool to cycle the ABS pump and valves to purge the air from the ABS.