AHG Auto Service » Make » Subaru » How do you bleed ABS on a Subaru?

How do you bleed ABS on a Subaru?

To bleed the ABS on a Subaru, there are a few different methods you can try. Here are some options based on the search results:
Bleeding ABS with an OBDII bi-directional diagnostic tool
According to a post on ScoobyNet.com, to bleed the ABS properly, you may need an OBDII bi-directional diagnostic tool that has the capability. One tool that is mentioned is the Foxwell NT630 Plus. However, it’s important to note that this method may require a specific tool and could be more expensive.
Activating the ABS pump
Another method mentioned in the search results is to activate the ABS pump. One user on Subaru Outback Forums suggested going out and activating the ABS on an empty road or lot, and then re-bleeding the calipers. This method involves using the ABS system itself to help remove air from the brake lines.
Cycling the ABS solenoids
The service manual for Subaru vehicles recommends cycling the solenoids in the ABS unit when bleeding the brakes. However, this can only be done if you have a Subaru select monitor, which is not commonly available to most people.
Bleeding each wheel separately
If you don’t have access to a diagnostic tool or the ability to activate the ABS pump, you can still bleed the ABS by bleeding each wheel separately. This process may take more time, as you will need to bleed each wheel individually. The exact procedure may vary depending on the specific Subaru model, so it’s a good idea to consult the vehicle’s manual or seek advice from a Subaru dealership or qualified mechanic.
Remember, it’s always important to follow the manufacturer’s recommendations and consult the vehicle’s manual for specific instructions on bleeding the ABS system.

How do you bleed air from ABS module without scan tool?

The general procedure is find some sand, gravel, ice, or snow, and drive around locking all the wheels up to activate ABS to purge air out, then bleed the brakes, then repeat till normal ABS function is observed and no sponginess.

How do you bleed a Subaru ABS module?

In general, whenever you are bleeding an ABS-equipped vehicle you can do so exactly as you would any other vehicle – stroke the pedal to pressurize the system, open a bleeder, close the same bleeder, and repeat. This does not change whether you are pressure-bleeding, vacuum-bleeding, or manual-bleeding.

Do you bleed ABS brakes with engine running?

Brakes are bled with the engine off. A running engine supplies a vacuum boost to the brake system. To properly bleed all the air from the system, there needs to be NO boost. Just pump the brake pedal until a solid pedal is felt, then bleed each caliper (if equipped) until the air is evacuated.

How do I reset my ABS module?

And you’ll know it’s on when all the lights start illuminating. And step number 2 come down below and three quick presses of your gas pedal. 1. 2 3 come back up top and wait a few moments in the event

Do you need a special tool to bleed ABS brakes?

In the practical maintenance or repair, the most commonly used method to bleed the braking system is noramally the manual bleeding, but if you want to make ABS bleeding get a better result, you will need a diagnostic scan tool as a helper.

Do you bleed brakes with reservoir cap on or off?

Locate your brake master cylinder reservoir’s brake fluid level, usually located under-the-hood. Ensure that your car has the appropriate amount of fluid. While you’re bleeding the brakes, you’ll want to be sure that you leave the master cylinder cap unscrewed but rest it on top of the reservoir.

Does the ABS pump need to be bled?

Bleeding is required when replacing an ABS modulator or other hydraulic components. It might not be necessary when performing a wheel-based hydraulic repair but you should be careful about not letting in any air into the system.

How do you clear ABS light on dashboard?

Disconnect and reconnect the battery: disconnecting the battery can reset the vehicle’s computer systems, potentially clearing the ABS light. However, this is usually a temporary fix and the light may come back on if there is an underlying issue.

How do you cycle an ABS pump?

Turn ignition to ON, do not start engine. As soon as the ABS warning light goes off, depress brake pedal and hold it. When ABS pump has finished cycling, turn ignition OFF.

How do I reset my Subaru ABS?

Position then we’re actually going to remove. This little pin from the number six. Position three times within 12 seconds.

AHG Auto Service

At AHG, we are committed to always providing our Perth customers with the best service and benefits when it comes to their vehicle servicing and repair needs. We have over 30 passenger and commercial vehicle dealerships in WA and can handle all of your car servicing needs no matter the make or model.

Leave a Comment