How do you adjust the headlights on a Honda HR-V?

Adjusting the Headlights on a Honda HR-V
To adjust the headlights on a Honda HR-V, follow these steps:
1. Park the vehicle on a flat surface facing a wall. This will ensure that the headlights are properly aligned.
2. Locate the adjustment screws. There are two adjustment screws on the Honda HR-V headlights. One is located on top of the headlight assembly, and it raises and lowers the headlights. The other adjuster is located on the inside part of the headlight assembly, and it moves the headlights left and right.
3. Have someone sit in the vehicle while you adjust the headlights. Ideally, this person should be of the same or similar weight as you.
4. Turn on the headlights. This will allow you to see the beam pattern and make the necessary adjustments.
5. Use the adjustment screws to align the headlights. Turning the top adjustment screw will raise or lower the headlights, while turning the inside adjustment screw will move the headlights left or right.
6. Make small adjustments and observe the beam pattern on the wall. Continue adjusting until the headlights are properly aligned and provide optimal visibility without blinding oncoming drivers.
Remember, it is important to adjust the headlights of your Honda HR-V for safety reasons. Properly aligned headlights ensure that you can see the road ahead clearly and avoid accidents, while also preventing the headlights from blinding other drivers.
I hope this helps! Let me know if you have any other questions.

How do you adjust headlight adjustments?

Adjust your headlights

1. Pop your hood and find your vehicle’s headlight adjustment bolts or gears. They should be behind the headlights.
2. Turn on your vehicle and flip on your low beams.
3. Use a socket wrench or screwdriver to slowly adjust the vertical direction of your driver’s side headlight.

How do you turn on low beam headlights on a Honda?

Rotate the switches on the lever to operate the exterior lights. Push the lever forward to turn on the high beams. Return the lever to its original position for low beams.

How do you turn on low and high beam headlights?

It you can manually turn the exterior lights off when the power is on and the vehicle is in park. And or the parking brake is applied rotate the end of the lever to the off.

How high should my headlights be aimed?

Once you’ve backed up, block one headlight and look at where the other beam falls compared to the markings you made on the wall. For vertical aim, the top of the most intense part of the beam should be at or below the centerline of your horizontal tapeline.

What is the correct height for headlights?

If they are not even, use a tape measure to measure how far up the wall the lower mark is and lower the other center line marker to the same height. These center lines should be no higher than 3.5 feet (1.1 m) from the ground.

At what height should headlights be aimed?

To properly adjust headlights you need to find the center point of the headlights first. You mark that height on your wall and then back up 25′. The cutoff for your low beam should be at or below the center point mark on the wall.

How do I adjust my headlights up or down?

As you stand in the front of the car, have the assistant turn the headlights off. Next, put the dark cloth or cardboard over one headlight, and have the assistant turn the headlights on. Find the adjusting screw and turn the screws slowly clockwise to raise the height of the lights or counterclockwise to lower them.

Where are the headlight adjustment screws?

Open the bonnet and look at the back of the headlight casing, on most models there will be two adjustment screws/bolts on the rear or top of each headlight-locate them and grab the right tool in order to turn them (check the owner’s manual to be sure they’re the right ones).

How do you turn on low beams on a Honda HRV?

High Beams
When the headlights are on, push the lever forward. Pull the lever back to return to low beams.

How high should headlights be at 25 feet?

Headlamp Aiming Criteria: at the correct distance (25′), a reject would occur if the brightest portion of the beam is more than 4” to the right or more than 4” to the left of the vertical center line or more than 4” above or more than 4” below the horizontal center line.