How do you adjust the headlights on a 2013 Ford Explorer?

Adjusting the Headlights on a 2013 Ford Explorer
To adjust the headlights on a 2013 Ford Explorer, follow these steps:
1. Prepare the vehicle: Park the vehicle on a level surface facing a wall or garage door that is approximately 25 feet away. Make sure the vehicle is at its normal ride height and that the tires are properly inflated.
2. Locate the adjustment screws: Open the hood of the vehicle and locate the adjustment screws on the back of the headlight assembly. These screws are used to adjust the vertical aim of the headlights.
3. Adjust the headlights vertically: Use a screwdriver or a suitable tool to turn the adjustment screws clockwise or counterclockwise to adjust the vertical aim of the headlights. Turning the screws clockwise will lower the beam, while turning them counterclockwise will raise the beam. Adjust both headlights individually.
4. Check the alignment: After making the adjustments, turn on the headlights and observe the beam pattern on the wall or garage door. The top of the beam should be at or slightly below the height of the headlights and should be centered horizontally.
Please note that there is no horizontal adjustment available for the headlights on a Ford Explorer. The headlights are properly aimed at the assembly plant, and if the vehicle has been in an accident, the alignment should be checked by an authorized dealer .
It’s important to consult the vehicle’s owner’s manual for specific instructions and to ensure that the adjustments are done correctly and safely.
I hope this helps! Let me know if you have any other questions.

How do you calibrate headlight height?

Things You Should Know
Pop the hood and look for adjustment screws on top of each bulb. Adjust these screws as needed until your headlights are correct. The lights are correct when the area below the horizontal line is illuminated and the bright spots are centered on the middle of each +.

What is the correct headlight alignment?

The top of the low beam shining on the wall should be at or slightly below the height of the center of the headlight lens for most vehicles. You should expect the light pattern to be higher on the right side (passenger side) to illuminate road signs and lower on the driver’s side to prevent blinding other drivers.

At what height should headlights be aimed?

To properly adjust headlights you need to find the center point of the headlights first. You mark that height on your wall and then back up 25′. The cutoff for your low beam should be at or below the center point mark on the wall.

How do I adjust my headlights up and down?

Find the adjusting screw and turn the screws slowly clockwise to raise the height of the lights or counterclockwise to lower them. As you make your adjustment, make sure the most intense part of the headlight beam hits at or just below the vertical centerline you taped on the wall. Adjust the horizontal field.

What is the correct height for headlights?

These center lines should be no higher than 3.5 feet (1.1 m) from the ground. If your two lights aren’t even, measure the distance from the ground to your bulb. Then, transfer that measurement to the wall to figure out which + sign is too high or too low.

How high should headlights be at 25 feet?

Headlamp Aiming Criteria: at the correct distance (25′), a reject would occur if the brightest portion of the beam is more than 4” to the right or more than 4” to the left of the vertical center line or more than 4” above or more than 4” below the horizontal center line.

What is the proper headlight alignment?

The top of the low beam shining on the wall should be at or slightly below the height of the center of the headlight lens for most vehicles. You should expect the light pattern to be higher on the right side (passenger side) to illuminate road signs and lower on the driver’s side to prevent blinding other drivers.

Where are the headlight adjustment screws?

Open the bonnet and look at the back of the headlight casing, on most models there will be two adjustment screws/bolts on the rear or top of each headlight-locate them and grab the right tool in order to turn them (check the owner’s manual to be sure they’re the right ones).

How do you make sure your headlights are aligned correctly?

Turn the side screws or bolts carefully until the most intense part of the headlight beam is just to the right of the tape’s vertical line. You can then check to see if both headlights line up close enough to the tape marks you’ve created on the wall. Continue to make any necessary adjustments until they look right.

How do you adjust the headlights on a Ford Explorer?

We’ll come to this side and you’ll also you see it right there. And you want to be careful because they are plastic gears. You don’t want to over tighten or force it to loosen.