OBD Port in a 1995 Dodge Ram
The OBD port in a 1995 Dodge Ram 2500 is typically located above the gas pedal in the driver’s footwell. In most cases, the location of the OBD port in any Dodge Ram 2500 made between 1993 and 2001, including the 1995 Dodge Ram 2500, is just above the gas pedal in the driver’s footwell. In some vehicles, the port may be hidden behind a removable plastic panel, so it’s advisable to check thoroughly. If you’re still having trouble locating the connector port, you can consult the owner’s manual for more information on where to find it.
It’s important to note that the 1995 Dodge Ram is OBD I, not OBD II. OBD ports were mandated to always be on the driver’s side near the steering column, on, or under the dashboard. Additionally, for a 1995 Dodge Ram, you can retrieve the codes by cycling the key on and off three times within 10 seconds and counting the flashes of the check engine light.
So, to answer your question, yes, a 1995 Dodge Ram has an OBD port, and it is typically located above the gas pedal in the driver’s footwell. However, it’s important to keep in mind that the 1995 Dodge Ram is OBD I, not OBD II .
Contents
What year did they switch from OBD1 to OBD2?
OBD-II became the nationwide standard in 1996. Compared to OBD-I, OBD-II is improved in standardization and capability. The standard OBD-II specifies the diagnostic connector and the corresponding pinout has electrical signal protocols and includes a messaging format.
Is my truck OBD1 or OBD2?
The OBD connector is a 16-pin connector that is usually located under the dashboard on the driver’s side. If your car has a 16-pin connector, then it has OBD2 or EOBD. If your car has a different type of connector, then it has OBD1. You can also check your car’s owner’s manual to find out which OBD system your car has.
What year cars use OBD1?
On-Board Diagnostics – First Generation (OBD1)
With the exception of some 1994 and 1995 vehicles, most vehicles from 1982 to 1995 are equipped with some type of first-generation On-Board Diagnostics.
Is there an OBD1 scan tool?
Safely and easily access the on-board computer to read ECM and ABS codes on most General Motors vehicles (domestic cars & trucks) from 1982 to 1995.
Do 1995 cars have OBD?
Additionally, a small number of 1994 and 1995 model year gasoline vehicles were equipped with OBD II systems. To verify that your vehicle is equipped with OBD II, you can look for the words “OBD II” on the emission control information label attached to the underside of the vehicle hood.
Does 1995 have OBD2?
94.5 and older were obd2, all of 95 have obd2, and the rest is history!!!
What is code 23 on a 1995 Dodge Ram 1500?
Code 23 is for the intake air temperature sensor. If you have had anything under the hood disconnected it would set this code, a sensor or wiring problem would also.
Where is the OBD port on a 1995 Dodge Ram 1500?
It is located under the dash on the drivers hand side to the right of the steering column. Check there first. My references could be wrong. If it is not there, check under the dash to the left of the steering column or even under the hood on the left or right side near the firewall.
Is 1995 OBD1 or OBD2?
All 95s, despite what you might read on the internet, are OBDI. They have an OBDII connector but remain OBDI.
What year did OBD1 start?
1988
1988 — Standardization of on-board diagnostics came in the late 1980s after the 1988 SAE recommendation that called for a standard connector and set of diagnostics. 1991 — The state of California required all vehicles to have some form of basic on-board diagnostics. This is referred to as OBD I.